歡迎光臨濰坊市正邦重工機械有限公司!Welcome to Weifang Zhengbang Heavy Industry Machinery Co., Ltd!
熱門關鍵詞Hot Keywords:洗沙機/sand washing machine,洗沙設備/sand washing equipment,廣東洗砂機/Guangdong sand washing machine,洗砂機/sand washing machine
高級搜索:
輪斗洗沙機保養的六個重要步驟/Six important steps for maintenance of wheel bucket sand washing machine

來源: 時間:2018-05-10 16:00:26 次數:

輪斗洗砂機作為一種常用于制砂生產線、建筑工地、水電站混凝土預制廠等行業的砂石洗選設備,在工作中難免收到砂石物料與洗沙廢水的侵蝕,影響設備的使用壽命。因此,輪斗洗砂機在日常使用中應該對其進行定期的保養,下面,就給大家介紹一下輪斗洗沙機保養的六個重要步驟。 As a kind of sand washing equipment commonly used in sand production line, construction site, concrete prefabrication plant of hydropower station and other industries,

輪斗洗砂機作為一種常用于制砂生產線、建筑工地、水電站混凝土預制廠等行業的砂石洗選設備,在工作中難免收到砂石物料與洗沙廢水的侵蝕,影響設備的使用壽命。因此,輪斗洗砂機在日常使用中應該對其進行定期的保養,下面,就給大家介紹一下輪斗洗沙機保養的六個重要步驟。

      一、在輪斗洗砂機每次的開機工作前,應該對洗砂機的潤滑點進行檢查,看潤滑油有無異常,是否有足夠的潤滑由,防止潤滑油干涸影像設備運行,并做到定期加注潤滑油。

      二、定期的檢查輪斗洗砂機的各個部件螺釘是否有松動的現象。注意,對于地腳螺栓要尤其的注意,若發現松動失效的話,要及時的進行重新固定。


      三、定期的檢查輪斗洗砂機的各個零部件是否有磨損,對其磨損情況進行檢查記錄,若磨損嚴重的應及時的更換。

      四、輪斗洗沙機在工作時,啟動電機后一定要等設備而運轉正常后,再工作,工作時應先開水泵調整至合適的水流量后,再開始逐漸加料。

      五、輪斗洗沙機工作結束停止運轉前,應先停止給料,待確定設備中物料排干凈了才再停機。

      六、停機后,若發現輪斗洗砂機內有沉積的廢水或是粉塵等沉淀物至,應該及時的清除,以免增加設備負荷,影響以后的工作。

      以上是輪斗洗沙機保養的六個重要步驟,希望能夠對大家有所幫助!

As a kind of sand washing equipment commonly used in sand production line, construction site, concrete prefabrication plant of hydropower station and other industries, it is difficult to avoid the erosion of sand materials and sand washing wastewater in the work, which affects the service life of the equipment. Therefore, the wheel et sand washing machine should be regularly maintained in daily use. Next, I will introduce six important steps for maintenance of the wheel et sand washing machine.
I. before each start-up of the wheel et sander, the lubricating points of the sander shall be checked to see if the lubricating oil is abnormal and if there is enough lubricating reason, to prevent the lubricating oil from drying up and the operation of the imaging equipment, and to fill the lubricating oil regularly.
2. Regularly check whether the screws of all parts of the wheel et sand washing machine are loose. Note: pay special attention to the foundation bolts. If any looseness or failure is found, they shall be fixed again in time.
III. regularly check whether all parts of the wheel et sand washing machine are worn, and check and record the wear condition. If the wear is serious, replace it in time.
IV. when the wheel et sand washing machine is working, it must wait for the equipment to run normally after starting the motor, and then it can work. When it is working, the water pump shall be turned on to adjust to the appropriate water flow before gradually feeding.
V. before the wheel et sand washing machine s working, the feeding shall be stopped first, and the machine shall not be stopped until the materials in the equipment are completely discharged.
Vi. after shutdown, if there is sediment such as waste water or dust in the wheel et sand washing machine, it shall be removed in time to avoid increasing equipment load and affecting future work.
The above are six important steps for the maintenance of wheel et sand washing machine. I hope it can help you!


不卡一卡二卡三网站